HandHeld Entertainment SV Series Manuel d'utilisateur Page 7
- Page / 120
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
i
Chapter 1 - Quick Check SV Series
Introduction........................................................................... 1-1
SV Series Model Specifications .......................................... 1-2
ScanView Software .............................................................. 1-2
Laser Beam ........................................................................... 1-2
Chapter 2 - Control Panel
Reset Button.......................................................................... 2-1
Turn Off Laser Beam ..................................................... 2-1
Perform Calibration........................................................ 2-1
Reset Ports...................................................................... 2-1
I/O Connector ...................................................................... 2-1
+ 5 VDC Power Input........................................................... 2-2
Sync Inputs ........................................................................... 2-2
Edge Sync Mode ............................................................ 2-4
Envelope Sync Mode ..................................................... 2-4
Communication Sync Commands ........................................ 2-5
Output Ports .......................................................................... 2-5
System Displays.................................................................... 2-6
Power/Sync LED............................................................ 2-6
Calibration LED ............................................................. 2-6
Read LED....................................................................... 2-6
Indicator LEDs 1 and 2 .................................................. 2-6
Chapter 3 - Serial Port Connector
Serial Port Specifications...................................................... 3-1
Serial Port Pin-out................................................................. 3-1
Serial Port Transmission Format .......................................... 3-1
Chapter 4 - ScanView Installation and Setup
Introduction........................................................................... 4-1
System Requirements ........................................................... 4-1
ScanView Software Installation ........................................... 4-1
Table of Contents
- User’s Guide 1
- Disclaimer 2
- Canadian Notice 3
- Statement of RoHS Compliance: 4
- Cautions 4
- Enclosure Description 5
- Table of Contents 7
- Chapter 5 - Scanner Setup 8
- Distance and Angle 10
- Quick Check SV Series 11
- ScanView Software 12
- Laser Beam 12
- Control Panel 13
- + 5 VDC Power Input 14
- Sync Inputs 14
- Edge Sync Mode 16
- Envelope Sync Mode 16
- Communication Sync Commands 17
- Output Ports 17
- System Displays 18
- Serial Port Connector 19
- Symbology Identifier Table 22
- System Requirements 25
- PC Communication Port Setup 26
- Select Graphs 27
- Toggle Display Updating 29
- Toggle Additional Results 29
- Download New Firmware 29
- Port Configuration 29
- Initialize the Com Port 29
- Zoom In 30
- Erase Current Session Data 30
- Reflectance Profile 30
- Transmit SV Commands 31
- Report an Analysis 31
- Session Mode 31
- Session Mode Notes 31
- Reflectance Profile Mode 32
- Bar Code Analysis Screen 32
- Bottom Panel 33
- Graph Display Area 34
- Right Panel 34
- Reflectance Profile Screen 35
- Scanner Setup 37
- Scanner Positioning 38
- Bar Code Travel Direction 39
- Good Reflectance Profile 42
- Picket Fence Direction 43
- Calibration 44
- SV Command Language 49
- A value of 00 clears (dis 52
- Diagnostic Commands – D 53
- Label Setup Commands – L 59
- Note: See 62
- (page 6-17) 62
- Table of Analysis Parameters 67
- Table of Action Parameters 69
- System Control Commands – S 72
- Checking SV Status with ~HT 73
- Mode 00 (~LV00) 78
- Mode 01 I/O operation 79
- Mode 01 LED Operation 79
- Mode 02 I/O operation 81
- Mode 02 LED Operation 82
- Mode 12 I/O operation 84
- Mode 12 LED Operation 85
- Mode 16 I/O operation 87
- Mode 16 LED Operation 88
- I/O operation 90
- LED Operation 91
- Mode 20 (~LV20) 100
- Reference Decode 102
- Technical Specifications 103
- ± .25 volt 104
- Operation Modes 105
- Parameters Analyzed 106
- Maintenance/Customer Support 109
- Product Service and Repair 110
- Limited Warranty 111
- Introduction 113
- Setting the Proper Scan Angle 114
- Calibration Hints 117
- Hand Held Products, Inc 120
© 2020, manymanuals.fr. Tous droits réservés | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels